Page 37 of 67 FirstFirst ... 27353637383947 ... LastLast
Threads 721 to 740 of 1330

Forum: General Injection Molding

Post all Injection Molding Related questions here.
Please Note:
1. This is not an advertising forum - please do not register to advertise your services here.
2. Please report if you receive any spam through private messaging.

  1. Tool Steel For Medical Molding

    Started by joeprocess, 9th November 2016 01:29 PM
    • Replies: 1
    • Views: 5,482
    JayDub
    10th November 2016, 10:19 PM Go to last post

  2. Can an injection molding machine be (easily) converted into a filament extruder?

    Started by seb3dge, 10th November 2016 01:19 PM
    • Replies: 1
    • Views: 4,698
    JayDub
    10th November 2016, 09:46 PM Go to last post

  3. Part thickness change for one run to another

    Started by joeprocess, 31st October 2016 04:17 PM
    • Replies: 7
    • Views: 8,891
    Brisli
    10th November 2016, 04:06 PM Go to last post

  4. Radel R-5800T Pre-Colored

    Started by joeprocess, 31st October 2016 04:34 PM
    • Replies: 10
    • Views: 10,680
    joeprocess
    3rd November 2016, 10:04 PM Go to last post

  5. Haitian IAPETUS 281 Ton 2 shot machine

    Started by pjhall, 3rd November 2016 06:55 PM
    1 Attachment(s)
    • Replies: 0
    • Views: 3,848
    pjhall
    3rd November 2016, 06:55 PM Go to last post

  6. How does this get molded?

    Started by William Wonkum, 1st November 2016 03:31 PM
    1 Attachment(s)
    • Replies: 1
    • Views: 3,001
    moldingppm
    2nd November 2016, 03:18 PM Go to last post

  7. Purchasing new Electric Machine

    Started by tommygolf85, 10th July 2016 12:18 AM
    • Replies: 11
    • Views: 7,363
    joeprocess
    31st October 2016, 04:03 PM Go to last post

  8. First Machine Brand?

    Started by Mad_Scientist, 29th March 2016 07:27 PM
    • Replies: 9
    • Views: 7,158
    iautry1973
    30th October 2016, 01:40 AM Go to last post

  9. Question Aluminum / aluminium tooling question?

    Started by debun, 6th July 2016 04:39 PM
    aluminium, aluminum, aluminum mold, gate, gate design
    • Replies: 6
    • Views: 6,648
    iautry1973
    29th October 2016, 11:50 PM Go to last post

  10. Mold Open End Alarm

    Started by Sunny, 26th October 2016 07:34 AM
    • Replies: 3
    • Views: 5,236
    Sunny
    28th October 2016, 04:53 AM Go to last post

  11. What should be the nominal temperature to operate LDPE material?

    Started by Sunny, 24th October 2016 09:02 AM
    • Replies: 4
    • Views: 3,069
    Sunny
    28th October 2016, 04:50 AM Go to last post

  12. Post tolerance for slip fit joint?

    Started by Orlando, 23rd October 2016 02:24 PM
    living hinges, mattel joints, polypropylene, tolerance
    • Replies: 2
    • Views: 3,190
    symphony
    26th October 2016, 06:57 AM Go to last post

  13. tolerances for mating parts?

    Started by Orlando, 22nd October 2016 02:53 PM
    living hinges, mattel joints, polypropylene, tolerances
    • Replies: 0
    • Views: 3,997
    Orlando
    22nd October 2016, 02:53 PM Go to last post

  14. Thinwall moulding

    Started by chintu2525, 30th May 2016 05:35 PM
    • Replies: 4
    • Views: 3,826
    Josue
    20th October 2016, 06:53 PM Go to last post

  15. Dry cycle time

    Started by Sunny, 19th October 2016 06:55 PM
    • Replies: 2
    • Views: 13,477
    Sunny
    20th October 2016, 04:53 AM Go to last post

  16. Thermolator w/Negative pressure

    Started by floorat, 1st October 2016 05:59 AM
    • Replies: 4
    • Views: 4,903
    symphony
    17th October 2016, 10:03 AM Go to last post

  17. EPDM Rubber and NBR Rubber.

    Started by daniel, 16th October 2016 07:50 PM
    • Replies: 0
    • Views: 3,742
    daniel
    16th October 2016, 07:50 PM Go to last post

  18. Nissei NEX III

    Started by Jason S., 4th October 2016 08:36 PM
    • Replies: 0
    • Views: 3,683
    Jason S.
    4th October 2016, 08:36 PM Go to last post

  19. Injection Molded Plastic Bushing/Shaft Recommendations

    Started by Maurice, 23rd September 2016 05:47 PM
    1 Attachment(s)
    • Replies: 4
    • Views: 6,391
    rickbatey
    4th October 2016, 12:35 AM Go to last post

  20. Effect of back pressure on the final product

    Started by mohammdyou, 23rd September 2016 12:14 AM
    back_pressure
    • Replies: 1
    • Views: 4,859
    brutusjax
    29th September 2016, 05:37 PM Go to last post
Page 37 of 67 FirstFirst ... 27353637383947 ... LastLast

Forum Information and Options

Moderators of this Forum

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules